Roland SH-32 Bedienungsanleitung PDF herunterladen (Seite 66)

Chapter 3. Applying Effects to the Sound (INS-FX, REV/DELAY)

Setting the Reverb/Delay

You can set a variety of parameters in each Patch or Rhythm Set for

the Reverb/Delay selected with the effect type.

1. Confirm that the SH-32 is in Patch mode.

2. Rotate the FX/SYSTEM knob to select the “REV/DELAY”

parameter to be set.

fig.03-05

Parameters That Can Be Set

E.LEVEL (Effect Level)

Sets the level of the signal sent to the Reverb/Delay.

When using the Preview function (p. 21) while setting the effects

for Rhythm Sets, you can set the effect level for each selected

Rhythm Tone (percussion instrument) individually.

TIME (Reverb/Delay Time)

This sets the length of the reverberation sound when a reverb effect

is selected with the effect type setting.

When a delay effect is selected, this sets the time delay from when

the original sound is played until the delay sound is produced.

When a chorus effect is selected, this sets the time delay from when

the original sound is played until the chorus sound is produced.

FBK (Feedback)

When a delay effect is selected with the effect type setting, this sets

the volume at which the delay sound is re-input (feedback volume).

Higher values result in more repeats.

L-R SHIFT/MOD DEPTH (L-R Shift/Modulation

Depth)

When Stereo Delay is selected with the effect type setting, this sets

the time delay from when the original sound is played until the

delay sound is produced in the left and right channels (Left: from -50

to 0 msec; Right: from 0 to 50 msec). This allows you to shift the left

and right delay times relative to each other. When set to 0 msec,

there is no difference between the left and right sides.

This sets the depth of the modulation effect or the modulation of the

chorus sound when Modulation Delay or Stereo Chorus is selected.

HF DAMP/MOD RATE (HF Damp/Modulation

Rate)

This sets the cutoff frequency for the high end of the delay feedback

sound when Modulation Delay is selected with the effect type

setting. When not cutting the high frequencies, set this to “byp”

(bypass).

This sets the cycle for the modulation effect only when Modulation

Delay or Stereo Chorus is selected (units: Hz).

3. Press [VALUE ▼/▲] to set the value.

You can make settings for the selected parameter only when the

indicator at the left of the FX/SYSTEM knob is blinking.

4. When you finish making settings, press [EXIT] to end the

procedure.

5. To save the settings, press [WRITE] and carry out the write

procedure (p. 63, p. 70).

Applying Effects in

Performance Mode

Selecting the Effect Settings Used in

a Performance (Effect Source)

For the effect settings used in a Performance, you can select one of

the effect settings from the Patches or Rhythm Sets assigned to each

Part. The effect settings selected here are referred to as the effect

source.

When Selecting Insertion Effects

Settings

While holding down [INS-FX], press the button for the Part to which

the Patch or Rhythm Set with the effect settings you want to use is

assigned.

fig.03-09

Parts whose effect settings are used are indicated by the part

buttons that light up when [INS-FX] is pressed.

Unlike in Patch mode, where each Patch or Rhythm Set

includes its own effect parameters, Performance mode

uses the effect settings for the Patches and Rhythm Sets

that are assigned to Parts specified in each Performance.

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 ... 123 124

Kommentare zu diesen Handbüchern

Keine Kommentare

Roland SH-32 Bedienungsanleitung Seite 66

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Die Eingabegeräte Roland SH-32