Roland SH-32 Bedienungsanleitung PDF herunterladen (Seite 59)

Chapter 2. Creating Your Own Sounds

Chapter 2

Increasing and Decreasing the Rate

of Change in Volume According to

the Keyboard Position

(TIME KEY FOLLOW)

[TIME KEY FOLLOW]

Set this to have the time following the decay time of the amplifier

envelope altered according to the position of the key pressed. With

the amplifier envelope for the C4 key (Middle C) as the reference,

then when values are positive (+), then the higher the key being

pressed is above the C4 key, the shorter the time, with negative (-)

values creating longer times. Larger settings will produce greater

change.

Press [TIME KEY FOLLOW], causing the indicator to blink, then

press [VALUE ▼/▲] to set the value (from -10 to 10). When you

have finished making the settings, either press [TIME KEY

FOLLOW] once more, or press [EXIT], causing the [TIME KEY

FOLLOW] indicator light to go off.

fig.Time KF.e

Setting the Volume for Each Patch,

Rhythm Set, or Performance

fig.02-28

[LEVEL]

Sets the volume for each Patch, Rhythm Set, or Performance.

Press [LEVEL], causing the indicator to light up, then press [VALUE

▼/▲] to set the value (from 000 to 127). When you have finished

making the settings, press [EXIT], causing the [LEVEL] indicator

light to go off.

• In Rhythm Tone Edit (p. 69), this procedure sets the volume of

each individual percussion instrument in the Rhythm Set.

• In Part Assign mode (p. 71), the volume settings selected in

Performance mode are enabled, and these can be saved to

individual Performances.

Modulating the Sound

(LFO 1 & 2)

fig.02-29

The LFO 1 & 2 (Low Frequency Oscillator 1 & 2) section outputs

waveforms that are used for purposes that are different than those of

the waveforms from the OSC 1 & 2 section. The waves from LFO 1 &

2 are used to create cyclic, periodic changes in the pitch, brightness,

volume, and other aspects of the OSC 1 & 2 wave sounds.

LFO Arrangement and Functions

fig.01-02.e

Use the LFO to create cyclic changes (modulation) in a sound. There

are two LFOs (LFO 1/2), and these may affect OSC 1/2 (pitch),

FILTER, AMP (volume), and PAN. When an LFO is applied to the

OSC 1/2 pitch, a vibrato effect is produced. When an LFO is applied

to the FILTER cutoff frequency, a wah effect is produced. When an

LFO is applied to the AMP volume, a tremolo effect is produced.

Turning the LFO On and Off, and

Switching Waveforms

(LFO 1, LFO 2, FORM)

[LFO 1]/[LFO 2]

These switch the LFO 1/2 on and off. Press the button; the selected

LFO is on when the indicator is lit or blinking, and off when the

indicator light is off. When both LFO 1 and LFO 2 are on, the LFO

with the blinking indicator is the one being edited. To turn off the

LFO that is not being edited, press the blinking button.

• Pressing [LFO 1] and [LFO 2] simultaneously causes both

indicators to blink, and both LFO 1 and LFO 2 become the edited

objects, thus allowing you to make identical settings to the two

LFOs at the same time.

• By holding down [LFO 1] or [LFO 2] along with [EXIT], you can

clear the current LFO 1 or LFO 2 settings. You can then redo the

settings, starting from their default state.

C4C3C2C1 C5 C6 C7

-5

-10

Key

Time

OSC

PITCH

Envelope

FILTER

Envelope

AMP

Envelope

AMP

LFO 1 LFO 2

control signal

Patch

audio signal

1 2 ... 54 55 56 57 58 59 60 61 62 63 64 ... 123 124

Kommentare zu diesen Handbüchern

Keine Kommentare

Roland SH-32 Bedienungsanleitung Seite 59

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Die Eingabegeräte Roland SH-32