Roland VS-1824 Bedienungshandbuch PDF herunterladen (Seite 111)

111

Chapter 7 Using Internal Effects (VS8F-2)

Chapter 7

Recording a loop effect

This example explains how to use an effect loop while

recording so the effect is recorded as a permanent part of the

track.

General Strategy: Connect an effect loop in the Input Mixer,

assign the input to a stereo track and assign the effect return

to the same stereo track.

Details for this Example: Select Patch P024 “Long Delay” as

Effect 2, record Input 1 and Effect Return 2 onto stereo Track

9/10.

Begin by Selecting the Effect:

1. Press [PLAY (DISPLAY)].

2. Hold [SHIFT] and press [F3 (EFFECT A)].

3. Press [F4 (FX2)]. The Effect 2 screen appears in the

display. If “FX2” does not appear above [F4], press

[F6 (EXIT)] until it does. Then, press [F4 (FX2)].

4. Press [F2 (Sel)]. The effects list appears in the display.

5. Use the TIME/VALUE dial or [ ], [ ], [ ],

and [ ] to move the cursor to Effect Preset Patch P024

“Long Delay.”

6. Press [F4 (Exec)] or press [ENTER/YES] to select the

effect. The EFFECT 2 screen appears in the display.

Next, Set up the Mixer

1. Press the SELECT button for Input 1. The button

indicator lights, and the Input Mixer Screen appears in

the display.

2. Use [ ], [ ], [ ], and [ ] to move the

cursor to “FX1.” Or, press [F2 (FX2)]. If “FX2” does not

appear above [F2], press [PAGE] a few times until you

see “FX2,” and then press [F2 (FX2)].

3. Use the TIME/VALUE dial to change FX Switch to “Pst.”

4. Press [ ] and [ ] to move the cursor to the Effect

Send Level, and use the TIME/VALUE dial to change the

level to “75.”

Then Pan the Input to Center

Since Input 1 is a mono source and is being recording to a

stereo track, set the panning for Input 1 to “Center.”

1. Use [ ], [ ], [ ], and [ ] to move the

cursor to the “Pan” section.

2. Use the TIME/VALUE dial to change the panning to “0”

(center).

3. Press [PLAY (DISPLAY)] to return to the Playlist display.

Finally, Assign both Input 1 and Effects Return

2 to Stereo Track 9/10

1. Press [FADER/MUTE] so “TR” is lit.

2. Press and hold STATUS for Track 9 or Track10.

3. Press Input 1 SELECT so it is blinking.

4. Press Input 2 SELECT so it does not blink.

5. Press Effect 2 SELECT once. Both Input 1 and Effect

Return 2 are now routed to stereo Track 9/10.

Begin recording on Track 9/10 as usual. As soon as you are

done recording, re-route the effect return off the track. If an

effect return is assigned to a track, you won’t hear the output

of the effect (unless the track happens to be in Source or

Record status). To re-route the effect return back to the main

stereo mix—the MIX bus—hold the STATUS button for

Track 9 (or Track10) and the SELECT button for each effect

assigned to the track.

1 2 ... 106 107 108 109 110 111 112 113 114 115 116 ... 294 295

Kommentare zu diesen Handbüchern

Keine Kommentare

Roland VS-1824 Bedienungshandbuch Seite 111

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Musikinstrumente Roland VS-1824