Roland VS-2000 Betriebsanweisung PDF herunterladen (Seite 256)

256

Chapter 22 Specific Applications

Device ID

For this application, set this to “17.”

MIDI Thru (MIDI Thru Switch)

For this application, set this to “OUT.”

SysEx.Tx (System Exclusive Transmit Switch)

For this application, set this to “On.”

MMC (Midi Machine Control Mode)

For this application, set this to “MASTER.”

Control Type (Mixer Control Types)

For this application, set this to “Off.”

4. Hold [SHIFT] and press [EXT SYNC].

5. Use [ ], [ ], [ ], and [ ] to move the

cursor and use the TIME/VALUE dial to make the

settings as described below.

Sync Source

For this application, set this to “INT.”

Sync Gen. (Generator)

For this application, set this to “MTC.”

Sync MTC Type (MTC Type)

For this application, set this to “30.”

6. Press [PLAY (DISPLAY)] to return to the Playlist display.

VS-880/880EX Settings

1. Press [SYSTEM] until “SYS MIDI PRM?” is displayed

and press [YES/ENTER].

2. Press the PARAMETER RIGHT button until “SYS EX

RX” appears. Use the TIME/VALUE dial to select “ON.”

3. Press the PARAMETER RIGHT button until “MMC =” is

displayed and use the TIME/VALUE dial to select

“SLAVE.”

4. Press the PARAMETER RIGHT button until “OUT/

THRU =” is displayed and use the TIME/VALUE dial to

select “OUT.”

5. Press [SYSTEM] until “SYS SYNC/TEMPO” is displayed

and press [YES/ENTER].

6. Use the TIME/VALUE dial to select “EXT.”

7. Press the PARAMETER RIGHT button so that “MTC

TYPE” is displayed and use the TIME/VALUE dial to

select “30.”

8. Press [PLAY (DISPLAY)] to return to the main screen.

When you press PLAY on the VS-1680, both units will start

playing. The VS-1680’s stereo mix output will now contain

audio from both units.

You can also use this method to transfer digital audio

between the two VS recorders. Connect the DIGITAL OUT of

the master VS to the DIGITAL IN of the slave VS—since the

MTC generated by the master VS provides synchronization

to both VS recorders, its digital ouput must also supply

digital clock to the slave VS.

Using an External MIDI

Device to Control the Mixer

(Compu Mix)

The VS-1680 can send and receive mixer settings and fader

movements as MIDI messages. You can use an external MIDI

controller to control the VS-1680’s faders. You can also use an

external MIDI sequencer to record mixer settings and

movements during playback as MIDI song data, and the

mixer can be controlled automatically by the MIDI sequencer

when the song is played back later. This is referred to as

Compu Mix. Compu Mix uses Control Change messages or

System Exclusive messages.

Correspondence Between MIDI

Channels and Controller

Numbers

MIDI channels correspond to the mixer channels as shown in

the following charts. For channels paired using the Stereo

Link function, Control Change messages can be exchanged

using the odd-numbered channel’s MIDI channel. Control

Change messages transmitted via the even-numbered

channel’s MIDI channel are ignored.

When using System Exclusive Messages

When working in Compu Mix, you should normally use

Control Change messages. However, if the Control

Change messages affect the settings of other MIDI

devices in your setup, you can use System Exclusive

messages. For more detailed information about Control

Change messages and System Exclusive messages, refer

to “MIDI Implementation” (Appendices, p. 25).

1 2 ... 251 252 253 254 255 256 257 258 259 260 261 ... 281 282

Kommentare zu diesen Handbüchern

Keine Kommentare

Roland VS-2000 Betriebsanweisung Seite 256

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Musikinstrumente Roland VS-2000