Roland VS-2000 Betriebsanweisung PDF herunterladen (Seite 186)

186

Chapter 14 Other Useful Functions

3. Press [ ], and [ ] to move the cursor. Use the

TIME/VALUE dial to adjust each of the settings as

desired.

Stereo In Select

This setting determines which external input is assigned

to the STEREO IN bus.

Off:

The STEREO IN bus is not used.

Input 1/2:

Assigns INPUT jacks 1 and 2 to the STEREO IN bus.

Input 3/4:

Assigns INPUT jacks 3 and 4 to the STEREO IN bus.

Input 5/6:

Assigns INPUT jacks 5 and 6 to the STEREO IN bus.

Input 7/8:

Assigns INPUT jacks 7 and 8 to the STEREO IN bus.

Digital:

Assigns the DIGITAL IN connector (coaxial or optical) to

the STEREO IN bus.

Level:

Adjusts the volume level (0-127) of the STEREO IN bus.

Balance:

Adjusts the balance (L63—R63) for the STEREO IN bus.

4. Press [PLAY (DISPLAY)] to return to the Playlist display.

5. Adjust the STEREO IN bus level using the channel fader.

6. Press [FADER/MUTE] so the “IN” indicator is lit.

7. Use the ST IN fader to adjust the STEREO IN bus level.

8. After you’re finished adjusting the STEREO IN bus level,

press [FADER/MUTE] so “TR” is lit.

* You can quickly assign an INPUT jack to the STEREO IN

bus by holding [ST IN] and pressing the SELECT button for

the input you want. The inputs are assigned in pairs (Inputs 1

and 2, Inputs 3 and 4, Inputs 5 and 6, etc.).

Removing a Direct Current

Offset from the MIX Bus

When the level meters of a device (mixer etc.) connected to

the output of the VS-1680 may move even though no sound

is being output from the VS-1680, you may be experiencing a

direct current offset on the MIX bus that is being output from

the VS-1680’s MASTER outputs. This can be removed.

1. Press [PLAY (DISPLAY)].

2. Hold down [SHIFT] and press [F5 (SYSTEM)].

3. Make sure that the System Menu is displayed. If not,

press [F6 (EXIT)].

4. Press [PAGE] so that [F2] indicates “GLOBL,” and then

press [F2 (GLOBL)].

5. Use [ ], [ ], [ ], and [ ] to move the

cursor to “DC Cut,” and use the TIME/VALUE dial to

select the desired setting.

If “DC Cut” is not shown, press [F2 (Prm2)], and turn the

TIME/VALUE dial.

DC Cut

When this is turned on, any direct current offset on the MIX

bus will be removed before the VS-1680 MASTER outputs.

6. Press [PLAY (DISPLAY)].

Using the MONITOR Knob to

Adjust Channel Panning

You can use the MONITOR knob to directly adjust the pan

(or balance) of the specified channel.

1. Press [PLAY (DISPLAY)].

2. Hold down the [SELECT] button for the channel whose

pan you wish to adjust, and do so by turning the

MONITOR knob.

Be Careful!

If you turn the MONITOR knob without pressing

[SELECT], you will adjust the volume level. If you are

attempting to adjust panning and inadvertently turn the

MONITOR knob toward the right without pressing

[SELECT]—or if you let go of [SELECT] while turning

the knob, a high-volume noise capable of damaging your

amp or speakers may occur.

1 2 ... 181 182 183 184 185 186 187 188 189 190 191 ... 281 282

Kommentare zu diesen Handbüchern

Keine Kommentare

Roland VS-2000 Betriebsanweisung Seite 186

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Musikinstrumente Roland VS-2000