Roland VS-1680 Bedienungshandbuch PDF herunterladen (Seite 68)

Recording Procedure:

1. Hold down [REC] and press the STATUS button

for the track you wish to re-record.

2. Press [ZERO] to return to the beginning of the

song.

3. Press [PLAY] to begin playback of the song.

At this point, the performance that has already been

recorded on the track or tracks that you want to re-

record is monitored.

4. Press the STATUS buttons again.

The indicator alternately blinks red and orange. Now,

confirm that you can hear source you want recorded

to the track coming from the monitors.

5. During playback of the song, each time the button

is pressed, the monitor switches between source

and track. Using the input sensitivity knob, adjust

the volume of the source so that it matches that of

the prerecorded performance.

6. Once you have adjusted the input sensitivity, press

[STOP].

7. Press [LOOP].

The button indicator lights, and Auto Punch-In

Recording is enabled.

8. Press [AUTO PUNCH].

The button indicator lights. You are now set to do

Loop Recording.

9. Press [PLAY].

Playback of the song begins. The song is played back

until the end of the loop is reached, playback will

return to the loop start point, and repeat.

10. Press [REC] where you want to re-record. The VS-

1680 will then automatically go into record mode

at the point where the punch-in is set. Start the

song or performance then.

11. When you reach the point where the punch-in is

set, the VS-1680 automatically returns to playback

mode. Playback continues until the end of the

loop, and the loop repeats from the start point

once again.

12. With the next playback of the loop, listen to what

you recorded to check the result. If the recording

hasn’t turned out as you intended, repeat Steps 10

and 11.

13. Press [STOP] to stop the song.

14. Listen to the results of the recording once more.

Press [LOOP].

The button indicator goes off.

15. Press [AUTO PUNCH].

The button indicator goes off.

16. Return to the beginning of the song and press

[PLAY].

Recording to Other Tracks

(Overdubbing)

In multi-track recording, the normal process is to

record new tracks while listening to the performance

on previously recorded tracks played back. This is

referred to as “overdubbing.”

1. Select the tracks you want to play back. While

holding down [STOP], press the STATUS buttons

for the tracks you want to play back (i.e., that you

want to hear while overdubbing).

The button indicators light green.

2. Select the tracks to which you want to record.

While holding down [REC], press the STATUS

buttons for the tracks to which you want to

record.

The button indicators blink red.

3. Select the sources to record to the tracks. While

holding down the STATUS buttons for the tracks

you want to record to, press the SELECT buttons

for the input channels whose sources you want

assigned to the tracks.

The button indicators blink.

4. Now you are ready for overdubbing. Follow the

Steps 4–17 of “Recording to the Tracks” (p. 61), to

record and then check the content.

Recording on V-Track 2

The VS-1680 features 16 tracks, each of which contains

16 auxiliary tracks. These subsidiary tracks are

referred to as “V-tracks.” By using all of these tracks

to their full potential, you can create recordings of up

to 256 (16 x 16) tracks.

1. Press the SELECT button for the track whose V-

track you wish to switch.

The button indicator lights. The Track Mixer screen

appears in the display.

2. Press [F5 (V.Trk)]. If “V.Trk” does not appear in

[F5], first press [PAGE] until “V.Trk” is displayed,

and then press [F5 (V.Trk)].

Chapter 3 Multi-Track Recording

1 2 ... 63 64 65 66 67 68 69 70 71 72 73 ... 211 212

Roland VS-1680 Bedienungshandbuch Seite 68

Kommentare zu diesen Handbüchern

Roland VS-1680 Bedienungshandbuch Seite 68

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Musikinstrumente Roland VS-1680