Roland FJ-40 Bedienungsanleitung Seite 48
- Seite / 99
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
46
3 Maintenance
If Performing Cleaning Several Times at the [POWERFUL]
Menu Does Not Correct the Drop-out Problem
If performing cleaning several times at the [POWERFUL] menu does not correct the image drop-out problem, use the included cleaning
kit. For information on how to use the cleaning kit, refer to the following section, "Using the Cleaning Kit to Clean the Printing Heads."
Using the Cleaning Kit to Clean the Printing Heads
If image drop-out persists even after performing cleaning with the cleaning kit, or if the cleaning kit is used up, contact your authorized
Roland DG Corp. dealer or Roland DG Corp. service center.
The heads are consumable parts. The useful life is six billion shots per nozzle.
Cleaning using the cleaning kit should be carried out when automatic cleaning and forced cleaning from the
[HEAD CLEANING] menu fail to correct image drop-out. Remove any ink buildup of dust or grime around the
printing heads, which can cause image drop-out or ink drips. We also recommend performing periodic cleaning
using the cleaning kit to prevent problems like these during printing.
Before starting cleaning, read through this section carefully to familiarize yourself with the procedures, then
carry out the cleaning operations quickly and accurately.
Cleaning is performed while the caps on the printing heads are detached, so cleaning must be completed before
the heads dry out. It is suggested that cleaning be completed in ten minutes or less.
If it appears that cleaning operations may take more than ten minutes, stop the cleaning operations and follow
the steps below.
1. Return the carriage to standby position and cap the heads.
2. Attach the cover and tighten the screws.
3. Switch on the power, and from the [HEAD CLEANING] menu, carry out cleaning of the heads.
4. When the head cleaning ends, perform cleaning using the cleaning kit again.
Cleaning sticks -- 10 Tweezers -- 1 pair Sponges (for cleaning the hooks) -- 10
Checking the Included Items
The following items are packed with the cleaning kit. Before use, check to make sure they are present.
- FJ-500 1
- For the USA 2
- For Canada 2
- Table of Contents 3
- To Ensure Safe Use 4
- Ink cartridge 6
- Avis sur les avertissements 7
- À propos des symboles 7
- Utiliser l'alimentation 10
- 1 Introduction 11
- Front View 12
- Rear View 12
- Side View 13
- Inside the Front Cover 13
- Operation Panel 14
- 1-2 Making the Connections 15
- Connecting the Cable 16
- For a network connection 17
- 2 Basic Operation 18
- Ink cartridge ports 19
- Turn Over the Plate 20
- Install the Ink Cartridges 21
- 2-2 Powerup 22
- 2-3 Loading the Material 23
- Loading Roll Material 24
- W 1234 mm 25
- NORMAL BI-DIR 25
- Loading Sheet Material 26
- Installing the Media Clamps 27
- CLEANING 28
- TEST PRINT 28
- 2-5 Printing 29
- Pausing Printing Operations 30
- Stopping Printing Operations 30
- About the [EMPTY MODE] 31
- Setting the Printing Mode 32
- PRINT QUALITY 33
- BI-DIRECTION 33
- 2 Basic Operation 34
- PRINT AREA 36
- LEFT EDGE 36
- Feed Correction 38
- Bidirectional Correction 39
- Remove the Material 40
- 2-7 When Not in Use 42
- Switch to "O" 43
- 3 Maintenance 44
- Roland FJ-500 45
- Ver.1.00 45
- PIGMENT 8COLOR 45
- INK REMAINING 46
- O G c m 46
- K C M Y 46
- HEAD CLEANING 47
- Checking the Included Items 48
- * Do not touch these areas 49
- Performing Cleaning 50
- Continued on the next page 51
- Left-hand head 52
- 3 Maintenance 54
- Sponges (for cleaning hooks) 56
- BOTH HEADS 58
- INK CONTROL 59
- EMPTY MODE 59
- DRAIN TANK 60
- The POWER LED goes out 61
- Bottom plug 61
- Drain bottle 61
- Positioning groove 63
- 3-7 Cleaning 64
- SET CLEANING 66
- LIQUID[OGcmKCMY] 66
- REMOVE CLEANING 66
- 4 User's Reference 67
- HEAD HEIGHT 68
- HIGH LOW 68
- 4-3 Printing Area 69
- 4-4 Display Menus Flowchart 70
- To the [INK CONTROL] menu 72
- 4 User's Reference 73
- Description of Keys 74
- Description of Menus 76
- 4-6 Network Connection 79
- For Windows 80
- For Macintosh 80
- Settings for Windows 98/95 81
- Settings for Windows NT 4.0 81
- Settings for Macintosh 81
- For Windows 98/95 84
- For Windows NT 4.0 85
- 4-7 What to Do If 86
- O___G _c _m _ 89
- K __C M Y __ 89
- The material becomes jammed 91
- Printed lines are misaligned 92
- SET CARTRIDGE 94
- [OGcmKCMY] 94
- Messages 95
- 4-8 Specifications 96
- Interface Specifications 97
- Control Area 98
- RJ-45 (Ethernet) connector 98
- Roland License Agreement 99
Verwandte Produkte und Handbücher für Drucken & Scannen Roland FJ-40
Drucken & Scannen Roland CJ-540 Spezifikationen
(32 Seiten)
(32 Seiten)
Drucken & Scannen Roland FJ-40 Spezifikationen
(28 Seiten)
(28 Seiten)
Drucken & Scannen Roland CJ-540 Bedienungsanleitung
(120 Seiten)
(120 Seiten)
Drucken & Scannen Roland CX-300 Bedienungsanleitung
(102 Seiten)
(102 Seiten)
Drucken & Scannen Roland RA-640 Spezifikationen
(50 Seiten)
(50 Seiten)
(52 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 4.194 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern