Roland FJ-40 Bedienungsanleitung Seite 34
- Seite / 99
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
32
2 Basic Operation
Specifying a location in the feed direction
Use the [ ] and [ ] keys to move the material to the
location where you want to start printing.
In the figure, the next printing operation starts from the
location shown.
* For roll material, when the material has been returned
toward the back of the unit with the [
] key, manually
roll the material back onto the roll so that all of the
material at the back of the unit is stretched taut.
The next printing operation starts here.
Front edge of the material
Reflective tape
Knife guide
Print-start line
Original printing
area
New printing
area
Left-hand edge of the printing area Right-hand edge of the printing area
Setting the printing area in the left-right direction (the direction of carriage movement)
Printing area
* Returning the
start point in
the left-right
direction to its
original
location
Starting location in the left-right direction
Specifying a location in the left-right direction (the
direction of carriage movement)
Margin (setting on the computer)
To change the start point (origin point) for printing, use the
[BASE POINT] key. At this time, the printing area does not
change.
Follow the step in both "Specifying a location in the feed
direction" and "Specifying a location in the left-right direction
(the direction of carriage movement)" to set the start point.
Starting location in the
feed direction
Specifying a location in
the feed direction
Printing at the Desired Location
This sets the location where printing starts.
When [SHEET TYPE] is set to [OPAQUE], the width of the
printing area is set automatically (see "4-3 Printing Area").
To determine the desired printing area, follow the steps in
"Setting the printing area in the left-right direction (the direction
of carriage movement)" to set the width of the printing area.
When [SHEET TYPE] is set to [CLEAR], the printing area is
not set automatically, so set the printing area in the same way. If
this setting is not made, it is set to the default printing area for
the maximum loadable width for the FJ-600/500/400.
Canceling setup cancels the printing area.
Start point
(origin point)
Next printing
- FJ-500 1
- For the USA 2
- For Canada 2
- Table of Contents 3
- To Ensure Safe Use 4
- Ink cartridge 6
- Avis sur les avertissements 7
- À propos des symboles 7
- Utiliser l'alimentation 10
- 1 Introduction 11
- Front View 12
- Rear View 12
- Side View 13
- Inside the Front Cover 13
- Operation Panel 14
- 1-2 Making the Connections 15
- Connecting the Cable 16
- For a network connection 17
- 2 Basic Operation 18
- Ink cartridge ports 19
- Turn Over the Plate 20
- Install the Ink Cartridges 21
- 2-2 Powerup 22
- 2-3 Loading the Material 23
- Loading Roll Material 24
- W 1234 mm 25
- NORMAL BI-DIR 25
- Loading Sheet Material 26
- Installing the Media Clamps 27
- CLEANING 28
- TEST PRINT 28
- 2-5 Printing 29
- Pausing Printing Operations 30
- Stopping Printing Operations 30
- About the [EMPTY MODE] 31
- Setting the Printing Mode 32
- PRINT QUALITY 33
- BI-DIRECTION 33
- 2 Basic Operation 34
- PRINT AREA 36
- LEFT EDGE 36
- Feed Correction 38
- Bidirectional Correction 39
- Remove the Material 40
- 2-7 When Not in Use 42
- Switch to "O" 43
- 3 Maintenance 44
- Roland FJ-500 45
- Ver.1.00 45
- PIGMENT 8COLOR 45
- INK REMAINING 46
- O G c m 46
- K C M Y 46
- HEAD CLEANING 47
- Checking the Included Items 48
- * Do not touch these areas 49
- Performing Cleaning 50
- Continued on the next page 51
- Left-hand head 52
- 3 Maintenance 54
- Sponges (for cleaning hooks) 56
- BOTH HEADS 58
- INK CONTROL 59
- EMPTY MODE 59
- DRAIN TANK 60
- The POWER LED goes out 61
- Bottom plug 61
- Drain bottle 61
- Positioning groove 63
- 3-7 Cleaning 64
- SET CLEANING 66
- LIQUID[OGcmKCMY] 66
- REMOVE CLEANING 66
- 4 User's Reference 67
- HEAD HEIGHT 68
- HIGH LOW 68
- 4-3 Printing Area 69
- 4-4 Display Menus Flowchart 70
- To the [INK CONTROL] menu 72
- 4 User's Reference 73
- Description of Keys 74
- Description of Menus 76
- 4-6 Network Connection 79
- For Windows 80
- For Macintosh 80
- Settings for Windows 98/95 81
- Settings for Windows NT 4.0 81
- Settings for Macintosh 81
- For Windows 98/95 84
- For Windows NT 4.0 85
- 4-7 What to Do If 86
- O___G _c _m _ 89
- K __C M Y __ 89
- The material becomes jammed 91
- Printed lines are misaligned 92
- SET CARTRIDGE 94
- [OGcmKCMY] 94
- Messages 95
- 4-8 Specifications 96
- Interface Specifications 97
- Control Area 98
- RJ-45 (Ethernet) connector 98
- Roland License Agreement 99
Verwandte Produkte und Handbücher für Drucken & Scannen Roland FJ-40
Drucken & Scannen Roland CJ-540 Spezifikationen
(32 Seiten)
(32 Seiten)
Drucken & Scannen Roland FJ-40 Spezifikationen
(28 Seiten)
(28 Seiten)
Drucken & Scannen Roland CJ-540 Bedienungsanleitung
(120 Seiten)
(120 Seiten)
Drucken & Scannen Roland CX-300 Bedienungsanleitung
(102 Seiten)
(102 Seiten)
Drucken & Scannen Roland RA-640 Spezifikationen
(50 Seiten)
(50 Seiten)
(52 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.532 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern