Roland VK-88 Bedienungshandbuch PDF herunterladen (Seite 77)

Advanced Use

❍ TONE CABINET FX

(RING➝OD➝EQ➝AMP➝TONE➝REV,

RING➝OD➝EQ)

Specify how effects will be applied to the Organ Voice

signal that is sent to the ROTARY TONE CABINET

connector.

Turn the [VIBRATO AND CHORUS] knob toward the left

to select RING➝OD➝EQ➝AMP➝TONE➝REV, or

toward the right to select RING➝OD➝EQ.

Before you connect a speaker to the ROTARY TONE

CABINET connector, please refer to “Connecting a

Rotary Speaker” (p. 91).

❍ REVERB STRUCTURE

(ROTARY➝REVERB, REVERB➝ROTARY,

PARALLEL)

This parameter specifies how the rotary sound effect and

the reverb effect applied to the organ voice will be

connected.

Turning the [VIBRATO AND CHORUS] knob switches

the setting.

❍ FOLD BACK (ON/OFF)

Specifies whether or not the 16' wheel will be “folded

back” an octave in the lower range of the upper part and

lower part. When this setting is On, the pitch will be

folded back.

Adjusting the pitch to match another

instrument

❍ MASTER TUNE (-100cent–0–+100cent)

This is a fine adjustment to the pitch of the VK-88. You can

adjust the pitch of the entire instrument in 0.1 cent steps,

relative to the pitch of A4 (middle A) = 440.0 Hz.

→ 100 cents equals one semitone.

Transposing the entire VK-88

❍ KEY TRANSPOSE (-6–0–+5)

This transposes the entire VK-88. The value is in semitone

steps over a range of -6–0–+5. With a setting of 0, there

will be no transposition.

Setting Explanation

RING➝OD➝

EQ➝AMP➝

TONE➝REV

When a speaker is correctly connected to

the ROTARY TONE CABINET connector,

the audio signal that is output to the

ROTARY TONE CABINET connector will

have effects applied to it in the following

order: 1. Ring Modulator ➝ 2. Overdrive

➝ 3. Equalizer ➝ 4. Amp ➝ 5. Tone ➝6.

Reverb.

At this time, the ORGAN OUTPUT jacks

and MIX OUTPUT jacks will function as

monitor jacks for the audio output of the

ROTARY TONE CABINET connector.

When a rotary speaker is connected, the

ROTARY SOUND [ON] button is

disabled. The registration will not change.

RING➝OD➝

The audio signal that is output to the

ROTARY TONE CABINET connector will

have effects applied to it in the following

order: 1. Ring Modulator ➝ 2. Overdrive

➝ 3. Equalizer.

The organ voice signal that is output from

the ORGAN OUTPUT jack and MIX

OUTPUT jack will be processed by the

effects that are specified.

D BEAM type indicators Explanation

All indicators off

ROTARY➝

REVERB

“SPRING SHOCK” and “TONE WHEEL

BRAKE” indicators lit

REVERB➝

ROTARY

All indicators lit PARALLEL

Setting Explanation

ROTARY➝

REVERB

The rotary effect will be applied first. This

simulates the sound produced by a rotary

speaker that has been placed in a

reverberant room.

REVERB➝

ROTARY

The reverb effect will be applied first. Some

traditional tone wheel organs had a reverb

circuit that utilized a spring mechanism,

and was placed before the rotary speaker.

This setting simulates the result.

PARALLEL

The reverb effect and the rotary effect will

be applied in parallel. This reproduces the

effect obtained by using a tone cabinet that

has both a rotary speaker section without

reverb and a fixed (non-rotating) speaker

with a spring-type reverb unit.

On traditional tone wheel organs, the 16' wheel of the

lowest octave in the upper part and lower part was

designed to produce the same pitch as the 8' wheel. This

was because when chords are played in the lowest

octave, the sound tended to become muddy. The VK-88

allows you to choose either to fold back the pitch (as on

traditional tone wheel organs), or not to fold it back.

When Fold Back is turned off, the lowest twelve notes

will use the wheels of the pedal part, which sound

differently than the other wheels.

1 2 ... 72 73 74 75 76 77 78 79 80 81 82 ... 111 112

Kommentare zu diesen Handbüchern

Keine Kommentare

Roland VK-88 Bedienungshandbuch Seite 77

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Digitale Klaviere Roland VK-88