Roland PNC-950 Bedienungsanleitung PDF herunterladen (Seite 17)

Movable pinch roller (left)

Sheet

Guide line

Sheet

Sheet loading lever

Pinch roll frame

Back of the

PNC-950

Front of the

PNC-950

(5) After positioning the pinch rollers, make sure that the left and right edges of the sheet lie parallel to the guide lines, then raise the sheet

loading levers at the rear of the unit to lower the pinch rollers and secure the sheet in place.

(6) Press the SETUP key.

The tool carriage moves to the cutting origin point.

If, after pressing the SETUP key, the PEN MODE LED and POWER/ERROR LED are both blinking at the same time, the following is the

cause.

Press the SETUP key (for about 1 sec.) to make the SETUP LED go out and move the tool carriage to the right. Then lower the sheet

loading levers.

- The location of the pinch rollers is incorrect.

Move the pinch rollers until they are positioned correctly over the grit rollers, and load a sheet. Press the SETUP key to proceed. (This

makes the SETUP LED light up.)

- If DIP switch SW-9 is set to ON ("piece"), then the length of the loaded sheet is too short.

Load a sheet with a length (vertical dimension) of 100 mm (3-15/16") or over, and press the SETUP key to proceed. (The SETUP LED

lights up.)

If you are using any of the following kinds of sheets, neither of the methods described earlier will result in correct cutting.

- A scrap sheet or some other sheet with left and right edges that are not straight and may catch on the sheet guides

- A sheet with edge holes for sprocket feed that has no sheet layer (only base paper) along the hole area at the edges

Use the method described below to load the sheet.

* Set DIP switch SW-9 to OFF (roll sheet) and reset the power.

(1) Move the left and right pinch rollers all the way to their respective sides.

(2) Pass the end of the sheet between the pinch rollers and the grit rollers so that it extends from the front of the unit.

If you are using a rolled sheet, set the sheet base included with the PNC-950 at the back of the unit, place a rolled sheet on the sheet

base, and pull out slack from the roll.

(3) Move the sheet from side to side and align the left edge of the sheet with the guide lines to the front and rear of the grit rollers.

Make sure at this time that both edges of the sheet lie over the grit rollers.. (See “Reference -- Sheet Loading Position” on page 8.)

Move the left and right movable pinch rollers to the respective edges of the sheet. If a pinch roller does not move easily, it may help

to grasp the corresponding pinch roll frame (refer to illustration of step 4) at the back of the unit and move it together with the pinch

roller.

(4) If you are using a sheet scrap or some other sheet whose left and right edges are crooked, be sure to set the pinch rollers well inside

the edges so that the sheet does not come loose from the pinch rollers while cutting is in progress. If a sheet with sprocket-feed holes

is being used, make sure that the holes at the left and right edges are not placed atop the pinch rollers.

If You Are Using Another Kind of Sheet

(2) Lower the sheet loading lever.

Sheet loading lever

Lower

SETUP

→

The SETUP LED goes

out and the tool carriage

moves to the right edge

of the cutting area.

(3) Remove the sheet.

• Removing the Sheet

(1) Press the SETUP key.

Hold down for about 1 sec.

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 35 36

Kommentare zu diesen Handbüchern

Keine Kommentare

Roland PNC-950 Bedienungsanleitung Seite 17

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Drucken & Scannen Roland PNC-950