Roland Metaza MPX-80 Bedienungsanleitung PDF herunterladen (Seite 107)

105

Chapter 6 Appendix

6-1 What to Do If

 P. 36, "Loading Material Using the Adhesive Sheet," p. 41,

"Loading Material Using the Center Vise"

Is the origin point of the machine displaced?

The center of the table scale may not coincide with the

machine's printing origin point. The origin point of the

machine must be the center of the scale on the table. You

can check the origin point location by printing calibration

data. To correct displacement between the scale center

and the printing origin point.

 P. 95, "Adjustment of the Origin-point Location"

Striking is performed, but nothing is printed.

Is the material to be printed in line with the

parameters for printable material?

Prepare and use printable material.

 P. 33, "Preparing Material to Print"

If you’re not using a head cap, does the head

position match the surface height of the mate-

rial in the case that you do not use the head

cap?

Check if the head position matches the surface height of

the material in the case that you do not use the head cap.

Printing cannot be performed if the head position does

not match the height position of the material. Adjust the

head position and then tighten the knob rmly.

 P. 36, "Loading Material Using the Adhesive Sheet," p. 41,

"Loading Material Using the Center Vise"

Is the marking pin bent or broken?

When nothing is printed, and changing the location

where the material is loaded, the parameters for the ma-

terial, or the height of the head unit does not correct the

problem, then the marking pin may be bent or broken.

Try changing to an unused marking pin and carry out

test printing. If you can print with the new marking pin,

it means the marking pin you had been using is bent or

broken. Continue using the new marking pin.

 P.100, "How to Replace the Head"

The printed image is unattractive.

Are the settings for the material in the driver's

setting window correct?

Choose the composition of the loaded material.

Even if the composition of the material is the same,

the hardness of the printed surface may vary greatly

depending on the casting method, the composition of

impurities, the presence of plating, and so on. In such

cases, perform ne adjustment of the striking force to

match the material.

 P. 92, "Registering a Composition and Adjusting the Striking

Force"

Is the image printed clearly?

If the image is not printed clearly, adjust the brightness of

the image. Perform printing while increasing the bright-

ness of [Gamma] or [Brightness] in the driver's setting

window a little at a time. At this time, leave the material

loaded and perform overstriking at the same location.

Continue changing settings and performing printing

until you obtain the darkness you want.

 P. 75, "Checking the Finished Results in the Preview Win-

dow"

Are grayscale tones printed clearly?

When grayscale tones are indistinct, go to the setting

window for the driver (“Advanced” at the [Image Correc-

tion] tab) and adjust the force of striking. Perform printing

while leaving the value for [Impact--MAX] unchanged

and increasing the value for [Impact--MIN] a little at a

time. At this time, leave the material loaded and perform

overstriking at the same location. Continue changing the

settings in the driver's setting window and performing

printing until you obtain the darkness you want.

 P. 92, "Registering a Composition and Adjusting the Striking

Force"

More Information about Overstriking

The various setting values determined with overstriking

are eective only when performing overstriking under

identical conditions. The same results are not necessarily

obtained when printing is performed with a new piece of

material with only the conditions made the same, without

performing overstriking.

Is the marking pin worn?

Attractive printing may be impossible if the marking

pin becomes worn. Adjust the pin or change it to a new

one.

Not bent or

broken

Bent or broken Bent or broken

1 2 ... 102 103 104 105 106 107 108 109 110 111 112 ... 119 120

Kommentare zu diesen Handbüchern

Keine Kommentare

Roland Metaza MPX-80 Bedienungsanleitung Seite 107

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Drucken & Scannen Roland Metaza MPX-80