Roland PNC-950 Bedienungsanleitung

USER'S MANUALPNC-960PNC-910* This User's Manual is intended for PNC-960 and PNC-910.

43-2 DIP Switch SettingsDIP switches settings must be made only when the power is turned off.3 Basic Operation- All DIP switches are set to OFF when s

53 Basic Operation3-3 Installing/Removing a Blade Always make sure the power switch is OFF before installing (or removing) the cutter.- Do not touch t

63 Basic Operation3-4 Loading/Removing the MaterialTurning on the PowerSwitch on the power switch on the left side of the PNC-960/910.When the power s

73 Basic Operation- If you are using roll material, start with step 1.- If you are using piece material, start with step 2.- When using sprocket-feed

83 Basic OperationIf you are using any of the following kinds of materials, neither of the methods described earlier will result in correct cutting.-

93 Basic Operation6Feed out the lengthof material to be cut.7Return the fed-outmaterial.5Press the SETUPkey.To Perform Long CuttingWhen performing cut

10About the Cutting AreaMovable Pinch Roller (Right)[PNC-960]Movable PinchRoller (Left)About 1 mm(about 0.04")About 15 mm(about 9/16")* The

113-6 Cutting Test to Check Blade Force — , , , , and TEST KeysBefore carrying out actual cutting, you may wish to perform a "cutting test&qu

123-7 Downloading Cutting DataThe unit will begin cutting when it receives cutting data sent from the computer.Software Settings- When cutting with co

133-8 Applying the Completed CutoutOnce cutting has been completed, follow the procedure below for application instructions.111222333444Stick applicat

For the USAFEDERAL COMMUNICATIONS COMMISSIONRADIO FREQUENCY INTERFERENCESTATEMENTThis equipment has been tested and found to comply with thelimits f

14Performing a Self-testThe PNC-960/910 is equipped with a "self-test" function to conveniently allow you to check whether or not it is capa

154 Settings For Each Function4-1 Using a material effectively and cutting along thevertical dimension (Rotate function) -- ROTATE Keyand ROTATE LEDTh

164-2 Plotting on Paper Media -- PEN MODE Key and PENMODE LEDThe PNC-960/910 is also capable of plotting on paper media using plotter pens made by thi

175 About the BladeThis section indicates the proper cutting conditions for various types of materials, as well as blade lifespans. Cutting conditions

186 What to do if...If the PNC-960/910 doesn't run...Is the PNC-960/910 power on? Turn on the power (refer to "3-4 Loading/Removing the Mate

19• mode1InstructionCompatibilityInstructionCompatibilityInstructionCompatibilityInstructionCompatibilityInstructionCompatibilityInstructionCompatibil

208 Character Sets Automatic backspace8 Character Sets

21PNC-960 PNC-910Mechanism Media-movement methodDriving method Stepping motor (Micro-step)Maximum cutting area Width:584 mm (23")Length:24,998 mm

229 SpecificationsInterface Specifications[Parallel]Standard In compliance with the specifications of CentronicsInput signals STROBE (1 BIT), DATA (8

R5-970910

iTable of ContentsThank you very much for purchasing the CAMM-1 PNC-960/910.- To ensure correct and safe usage with a full understanding of this produ

iiTypographic ConventionsCopyright © 1996 ROLAND DG CORPORATIONTypographic ConventionsThis manual uses certain typographic symbols, outlined below. Th

iii To Ensure Safe UseTo Ensure Safe UseNever disassemble or modifythis product.Do not step on or damage the powercord, or allow heavy objects to bepl

ivAbout the Labels Affixed to the Unit/To Ensure Correct Use About the Labels Affixed to the UnitThese labels are affixed to the body of this product.

1Power Cord:1 Blade (ZEC-U1005):1 Blade Holder (XD-CH3):1 Roller Base:1Cutter Tool:1 Tweezers:1 Test-use High-quality Paper/Material for Test Cuts/Tes

22-2 Rear View2-3 Operation PanelPower Connector (AC IN)This connector accepts standard ACpower cord.Sheet Loading LeverThis moves the pinch rollers u

33 Basic Operation3 Basic Operation3-1 Setting Up and ConnectionWhen arranging setup space for the PNC-960, make sure you have a space that is at leas