Roland PK-5A Bedienungsanleitung PDF herunterladen (Seite 6)

PK-5A

Operation

• RETRIGGER (pedal

[B]

)

When this parameter is on, some special effects

can be obtained.

When in MONO mode, the pedalboard is mono-

phonic: if you press two pedals simultaneously,

only the last note played will sound. When that

note is released, the previous note will sound,

so a pleasant alternating effect can be

obtained.

To switch off the RETRIGGER parameter, press

the SELECT selector [9], then pedal

[B]

. All indi-

cators briefly light to confirm your selection.

• OCTAVER (pedal

[C]

)

When this parameter is on, a note is added to

each note you play. The added note is one

octave above the note you played.

Note:

If the OCT parameter is set to

[8]

, the added note

may be out of range of the receiving tone generator. In

that case, the PK-5A transposes the added note one

octave down.

To switch off the OCTAVER parameter, press the

SELECT selector [9] and pedal

[C]

. All indicators

briefly light to confirm your selection.

●

[10] PRG CHANGE

To send a program change number, press the

PRG CHANGE selector [10]; the corresponding

indicator lights.

Use the pedals to enter the desired PC number:

to send the program number “123”, press ped-

als

[1]

[2]

and

[3]

in succession. Then press pedal

[B]

(ENTER) to confirm the operation. All indica-

tors briefly light to confirm your selection.

If you pressed the wrong pedal while specifying

the number, you can cancel your input by

pressing pedal

[A]

(CANCEL).

If you wish to send the previously-entered pro-

gram change number again, simply press the

PRG CHANGE selector [10] and pedal

[B]

(ENTER). All indicators briefly light to confirm

your selection.

Note:

If a program change number higher than “128” is

entered, the PK-5A sends the previously-entered (cor-

rect) number when pedal

[B]

(ENTER) is pressed.

●

MIDI program changes & Bank Select mes-

sages (CC00 & CC32)

You can also add Bank Select information

(CC00 and CC32) to the program change num-

bers you transmit.

(1) Press the PRG CHANGE selector [10] (indica-

tor lights).

(2) Press pedal

[C]

to select the MSB/LSB func-

tion.

The indicator of the MONO mode now flashes.

(3) Use the pedals to enter the value for CC00.

Example: To set the CC00 (MSB) value to “16”,

press

[1]

and

[6]

(4) Confirm by pressing pedal

[B]

(ENTER).

The PK-5A now expects you to input a value for

CC32 (LSB). Repeat steps (3) and (4).

Note:

If you pressed the wrong pedal while specifying

the number, you can cancel your input by pressing

pedal

[A]

(CANCEL).

Note:

If you only need to enter a CC00 value, confirm it

by pressing

[B]

twice (so as to skip the CC32 value).

Note:

If a value higher than “127” is entered, the PK-5A

uses the previously-entered (correct) value for CC00

when pedal

[B]

(ENTER) is pressed.

(5) After entering (or skipping) the CC32 value,

you need to specify the program change

number to be transmitted along with the

MSB (and LSB) value(s).

See “[10] PRG CHANGE” for details. All indica-

tors briefly light to confirm your selection.

The entire operation sequence can be summa-

rized as follows:

(1) CC00

: selector [10]

→

[C]

→

use the pedals

to enter the value

→

[B]

(Enter) (or

[A]

(Cancel))

(2) CC32

*: use the pedals to enter the value

→

[B]

(Enter) (or

[A]

(Cancel))

(* Press

[B]

again to skip the CC32 value.)

(3) PRG

: use the pedals to enter the program

number

→

[B]

(Enter) (or

[A]

(Cancel))

●

[11] MIDI CHANNEL

To select a MIDI channel (1~16), press the MIDI

CHANNEL selector [11] (indicator lights).

Use the pedals to enter the MIDI channel you

wish to set. Example: to specify channel “15”,

press

[1]

and

[5]

. Then press pedal

[B]

(ENTER) to

confirm the operation. All indicators briefly

light to confirm your selection.

Note:

If you pressed the wrong pedal while specifying

the number, you can cancel your input by pressing

pedal

[A]

(CANCEL).

Note:

To return to the default MIDI channel (“2” in

MONO mode), press the MIDI CHANNEL selector [11]

and pedal

[C]

. All indicators briefly light to confirm your

selection.

Note:

If a MIDI channel number higher than “16” is

erroneously selected, the PK-5A will exit this function

when pedal

[B]

(ENTER) is pressed.

PK-5A book Page 6 Thursday, July 24, 2003 6:26 PM

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Kommentare zu diesen Handbüchern

Keine Kommentare

Roland PK-5A Bedienungsanleitung Seite 6

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Musikinstrumente Roland PK-5A